|
|
|
|
|
 |
 |
 |
The snake for the bell |
The snake for the slide |
The prop of the bell |
|
1/6$B!!(Bminiature model Trombone $B!!(B(Historical German series) I received the opinions. $B!T(BTrombone section of Berlin Phil. of an old good time is reproduced by the elaborate miniature.$B!U(B $B!T(BThe Vienna philharmonic adoption model in mid-1800$B!U(B $B!T(BDoes sound come out?$B!U(B Thank you very much. It is making to phon monochrome faithfully. Of course, it is also a mouthpiece. If there is a human being of 1/6 and basic practice etc. is done firmly, sound will come out. Since I think that there is also a portion whose length is not exact, in a pitch, it is diffident. Hand$B!!(BHammered.$B!!(BAll were begun to beat from board material except the slide pipe. I thought that I also saw and made the musical instrument of former Germany about in 100 years ago. As for the slide, the outside pipe and the inner pipe bought in the brass pipe from the pipe store. The stocking has rounded and soldered the german silver. The "spring" of a promise is contained in a No. 1 position and only one of the two has soldered the outside pipe support. A slide is the portion asked for machine accuracy but Since the crevice was already 0.1mm, he was prepared for not moving like a genuine article. Even so, it is the accuracy which he wants to take out to repair. |
 |
 |
 |
 |
Bell's paper pattern |
The brass plate is bent. |
If welding finishes... All black |
After beginning to beat |
|
The biggest problem is a bell. It is as the paper pattern of onepiece brass plate and the welding. Since it was the first experience, it failed fairly. The brass plate which became pipe-like is begun to beat. 20 or more have gone wrong so far. A genuine article begins to beat the metal plate of a thick eye rather than completion and although it will seemingly begin to delete to the target thickness, begin to beat this time -- it is said whether there is nothing -- since it was uneasy, the thin board was used. Since it was thin, the result was influenced. The paper pattern is changed about 5 times. But this photograph does not have a form which can still be satisfied, either. The kranz struck the plank of the nickel silver little by little, and made it the target form. Bell's tip has soldered the brass wire. There are many things to do for etching, a crown stamp, etc. |
 |
 |
 |
 |
There is also a lot of failure. |
Part array |
Attachment of kranz |
Completion of a prototype |
|
That one more worried is the work which bends a bell and the pipe of a slide junction part. It is said that an actual method pours the melted lead into a pipe, and bends it. "The metal which melts with hot water" found in the network came to hand this time. This was melted, and with the injector, it poured into the pipe and bent. Since the inner side of the bent pipe becomes wrinkles, it bends taking wrinkles. It is hard to take this. A slide side goes without difficulty but a bell side has a taper toward a bell from a slide. Therefore, since the pipe was made from the board, it was hard to take Siwa of a junction portion. The work which makes a pipe from a dual boa slide is likely to increase. Snake decoration was turning off the nickel silver sheet thinly, and bent it one animal at a time. the ball is what rounded the nickel silver. This snake referred to what was attached to the musical instrument PENZEL's$B!!(Bnachf.. The form of a snake is a Japanese too. The mouthpiece was learned and given to how to make the mouthpiece of the old horn found in the network. Although it is natural, on a trombone and a horn, a difference is in cup form. The Sachsen type was aimed at this time. It divided into two piece of the cup and the shank, and after beating the nickel silver plate $B!J(B0.3mm$B!K(B, low attachment is carried out and it began to delete. The mouthpiece of the Baroque$B!!(BTrombone is the form which the hole opened to the bottom of a hemisphere type cup. The mouthpiece of Sachsen type makes this hemisphere deep. The miniature making can prepare the same environment as the craftsmen of 100 years or more ago at home. But the machines, such as a lathe, a model iris diaphragm machine, and a pipe vending machine, were not able to be prepared. The problem has appeared in accuracy or finish. By fixing a tool, it covers to some extent. Completion. |
 |
 |
|
It puts on a palm. (10g) |
Left$B!'(BCountDownNo.10$B!!!!(BRight$B!'(BCountDownNo.9 |
|
$B!!!!!!!!!!!!!!!!!!!!(BWOW$B!*!*!!!!(BSecond Hand It is touch called the toy of tin elaborate with which. I will do my best in finish to a slight degree. I heard that at least manual labor A could be made. Next, it is also with F pipe. If a rotary can be made, it is applicable also to a horn or a trumpet. A dream spreads. When it gave it a try, a lack [ one's power ] has felt actually fully. And it is a word of respect to the craftsman who is making many manually. HOME $B!!!!(B Japanese $B!!!!(B English $B!v!!(BMail$B!!(BMe$B!!!'!!(Bif it makes Under information collection$B!*(B $B!v!!(B 
$B!!(BLink Free$B!!!'!!(BA janitor does not ask for it, and links permission and it is splendid. |
   |